BLUE SKY SUB 12 Troubleshooting Guide download pdf (Page 12)

Blue Sky Energy - Solar Boost 2512i-HV and 2512iX-HV

SYMPTOM PROBABLE CAUSE ITEMS TO EXAMINE OR CORRECT

Networked units do not

seem to coordinate

action or slaves do not

turn on

IPN network address set wrong

Network wiring problem

One unit of a multi-unit network must be set to IPN network address 0 (zero), AND all other units

must be set to different addresses 1 – 7.

Confirm wiring correctly in place. Use IPN-ProRemote or UCM to see View Charge Unit Status

screens to confirm communication with slaves.

Temperature related

functions do not work.

Temperature sensor not installed on master

Temperature sensor failed, reverse polarity,

or not BSE sensor p/n 930-0022-20.

Temperature sensor must be installed on the master in a multi-controller system.

If sensor is open, short, reverse polarity, wrong sensor or missing system will operate as if

sensor was at 25°C. Sensor temperature can be read directly on the IPN-ProRemote or UCM.

Proper sensor voltage when excited by the 2512 will be 2.98V at 25°C, changing at +10mV/°C.

SPECIFICATIONS

SPECIFICATIONS SB2512i-HV

Output Current Limit

25 amp maximum 36 cell modules • 20 amp maximum 60 cell modules

Nominal Battery Voltage 12VDC

PV Input Voltage

50VDC absolute maximum (Recommend maximum V

at STC ≤ 40VDC)

PV Input Power Recommended maximum, 340W with 36 cell modules / 270W with 60 cell modules

Power Consumption

0.30W typical standby • 1.0W typical charge ON

Charge Algorithm

3-stage Bulk/Absorption/Float • Charge time in Absorption fixed at 2 hours (Range 0 – 10 hours

)

Absorption / Float Voltage 14.2VDC / 13.2VDC fixed value (10.0 – 20.0VDC

)

Power Conversion Efficiency 96% typical @ 14 volt 20 amp output with 36 cell modules

Physical Configuration

and Dimensions

Open frame construction with conformal coated electronics mounted to rear of 5.3” x 5.3” (13.5cm x 13.5cm)

clear anodized aluminum face plate. Black ABS corrosion proof mounting box included, 2.5” (6.4cm) deep.

Analog Input Accuracy / Range

Battery / PV voltmeters, 35.0VDC / 55.0VDC ±0.50% FS • Input / Output ammeters, 30.0 amps ±0.50% FS

Communication IPN Network connector for IPN displays & UCM only. Complete IPN interface for multi-controller coordination not provided.

Environmental

-40 – +40°C, 10 – 90% RH non-condensing

Additional Specifications for SB2512iX-HV

Equalization Voltage / Time

15.2VDC fixed value (range 10.0 – 40.0VDC

) • Automatic fixed at 2 hours each 30 days, may be disabled

Auxiliary Output Functionality

• Aux. Battery Charge

• Load Control

• Lighting Control

Single output field configurable as either: 25 amp load controller –or– 2 amp auxiliary battery charger

2 amp typical, same charge voltage as primary battery

25 amp maximum; ON @ ≥12.6VDC / OFF @ ≤11.5VDC (Range 10.0 – 40.0VDC

), or net battery amp-hours

)

Variable Post-Dusk and Pre-Dawn timers

, Range 0.5 – 20.0 hours

Temperature Compensation

Optional battery temperature sensor, -5.00 mV/°C/cell correction factor (Range -0.00 – -8.00 mV/°C/cell

) • sensor range -60 – +80°C

Auxiliary Battery Voltage

Auxiliary battery voltmeter, 35.0VDC ±0.50% FS

Communication Complete IPN Network interface. Allows up to 8 IPN capable controllers to set up and operate as a single charging machine.

As a part of our continuous improvement process

With IPN-ProRemote or UCM which may be

specifications are subject to change without prior notice. used for setup only, or permanently installed.

5-YEAR LIMITED WARRANTY

Blue Sky Energy, Inc. (hereinafter BSE), hereby warrants to the original consumer purchaser, that the product or any part thereof shall be free from defects due to

defective workmanship or materials for a period of five (5) years subject to the conditions set forth below.

1. This limited warranty is extended to the original consumer purchaser of the product, and is not extended to any other party.

2. The limited warranty period commences on the date the product is sold to the original consumer purchaser. A copy of the original purchase receipt identifying purchaser

and date of purchase, must accompany the product to obtain warranty repairs.

3. This limited warranty does not apply to, and future warranty shall become void, for any product or part thereof damaged by; a) alteration, disassembly or application of a

foreign substance, b) repair or service not rendered by a BSE authorized repair facility, c) accident or abuse, d) corrosion, e) lightning or other act of God, f) operation or

installation contrary to instructions pertaining to the product, or g) cosmetic aging.

4. If BSE’s examination of the product determines that the product is not defective the consumer shall be charged a test and evaluation fee of $20 and be responsible for all

transportation costs and insurance related to returning the product to the consumer. The consumer is ultimately responsible for proper installation and operation of the

product and BSE’s prior troubleshooting assistance shall not serve as a waiver of the test and evaluation fee. The test and evaluation fee is subject to change without

prior notice.

5. If within the coverage of this limited warranty, BSE shall repair or replace the product at BSE’s sole discretion and return the product via standard ground transportation of

BSE’s choosing within the continental US. The consumer shall be responsible for all transportation costs and insurance to return the product outside the continental US,

and for all transportation costs and insurance related to expedited return of the product. BSE’s liability for any defective product or any part thereof shall be limited to the

repair or replacement of the product. BSE shall not be liable for any loss or damage to person or property, or any other damages, whether incidental, consequential or

otherwise, caused by any defect in the product or any part thereof.

6. Any implied warranty for merchantability or fitness for a particular purpose is limited in duration to the length of this warranty.

7. To obtain warranty repairs, contact BSE at 760-597-1642 to obtain a Returned Goods Authorization (RGA) number. Mark the outside of the package with the RGA

number and return the product, postage prepaid and insured to the address below. The consumer is responsible for all transportation costs and insurance related to

returning the product to BSE, and for any shipping damage which may void the warranty or increase the cost of repairs.

Blue Sky Energy, Inc.

2598 Fortune Way, Suite K

Vista, CA 92081 USA

760-597-1642 • Fax 760-597-1731 • www.blueskyenergyinc.com

1 2 ... 7 8 9 10 11 12

Comments to this Manuals

No comments

BLUE SKY SUB 12 Troubleshooting Guide Page 12

Comments to this Manuals

Related products and manuals for Subwoofers BLUE SKY SUB 12